A lush green carpet of lawn surrounding even a modest suburban home makes it seem more attractive and impressive. A good quality lawn can not only add to the appearance of your home, it can also increase its value, prevent soil erosion and help to absorb heat and noise to keep your environment cooler and quieter.
- Lawn Seed
- Lawn mower
- Fertiliser spreader
- Garden hose
- Hand aerator
- Digging fork
- Soil pH test kit
- Metal garden rake
Step 1: Planning
When shaping a new lawn, avoid corners or peaks too narrow for mowing – use groundcovers or bark mulches instead. Plan an expanse of lawn rather than cutting up the area with little garden beds which make mowing difficult. Your lawn will also need to come up to path levels and other established points like gates, fences, pool, etc. If possible, avoid very shaded positions – most grass species do not take kindly to shade under trees or beside buildings and fences. Use such areas for paving or bark-chips instead. For banks, consider planting ground covers which hold the soil better than grass and require little maintenance.
Also plan to plant in the periods that will give the best chance of success. Generally, this is in the spring or autumn, as summer and winter are usually too extreme for successful germination. Autumn is probably your safest time. Young grass planted in spring requires more water through summer and may not survive extreme heat.
Step 2: What type of lawn?
It’s important to choose a grass variety that is suitable for the climate and your soil type. It also must suit your lifestyle. Is it to be just ornamental? Or will it need to stand up to children’s play and other outdoor living activities?
There’s a variety of brands and grass seed mixtures on the market, from hardy mixes that love direct sunlight to shade loving blends for under trees and in quiet corners. So you’ll be able to find a mixture to suit any situation. Many also contain slow release nitrogen granules to progressively fertilise and assist early growth. Some also blend in clovers to help improve soil fertility.
You might even consider a non-grass lawn, such as Dichondra (kidney weed) which gives a smooth, green lawn that needs no mowing and is suitable for sun or light shade. If you have any trouble deciding, ask at Mitre 10. We’re happy to assist you.
Step 3: Site Preparation
The success of your lawn depends very much on proper preparation. This includes cultivation, drainage, soil improvement and grading or levelling. The objective is to have a firm, granular, well-drained, weed-free soil that is neutral or slightly acid.
Use your mattock or pick to first remove all stones, rocks, big lumps of clay and other rubble. Cultivation (digging and turning the soil over) will destroy most annual weeds, and ‘Zero’ or ‘Round-Up’ can be used to kill more persistent varieties. Dig the soil to spade depth – about 15cm.
If it’s a large area or clay soil, you’d be better off hiring a rotary hoe. It will also help if you water the area the day before you dig or rotary hoe. Water the newly dug soil well and leave it for a few weeks.
This will allow weeds to come up so you can kill them before sowing your lawn seed.
Look to see if water is draining away satisfactorily next time it rains, or if it lies about. If drainage is poor, lay in some Agi Pipe or Slotted Drain Pipe now. Poorly drained lawns develop problems with mosses and other water-loving weeds which will give you years of trouble. For a small site, only one drain running across the middle and following the natural fall of the land is needed.
For larger areas, set feeder drains at an angle of about 40 deg. Set drain lines about 22cm deep and fill to near the surface with 6mm gravel or crushed rock, then sand.
If you have heavy clay soil, now’s the time to improve soil structure and water penetration by applying gypsum at 1 or 2kg per sq. metre. Top dress this with about 5cm of sandy loam and cultivate to about 10cm deep.
Use your pH Soil Test Kit to check the soil acidity. Many soils are too acid (sour) for good growth and an acidity reading below 6.0 means the soil should be treated with garden lime to correct it. Apply the lime at about 200g per sq. metre.
Also add a complete lawn fertiliser to stimulate weed growth that otherwise may not appear until after sowing.
Level off high spots and fill hollows either by using your garden rake or by attaching a rope to a heavy board and dragging it over the site.
If a heavy board isn’t handy, fasten several lighter ones together. Your drag rope must be attached about 7 or 8cm back from the front edge. If it’s too far back, the front edge will bite too deeply. If it’s too far forward, the board will just skim the surface without scraping off the bumps. Make sure the soil is not too compacted though. If it feels spongy underfoot, dampen it and give it a good rolling or systematically tread the soft spots to consolidate them.
Step 4: Sow your seed
To begin, use a starter-type fertiliser even if your seed mixture contains a small amount of release fertiliser. Follow the instructions on the pack and rake into the surface.
Seed should be placed at a fairly shallow depth, generally about 5 to 10mm below the surface. Use your metal rake to make shallow grooves in the soil, then scatter seed evenly over the area. Sow half your seed in an east-west direction, and the remaining half in a north-south direction. This will ensure a more even coverage. Lightly smudge across the surface with a piece of timber to bury the seed in the groove and firm down the surface with your rake head. Don’t worry if the seed is not all covered.
To ensure even sowing, try mixing your seed with dry white sand if your soil is dark, or a black sandy loam for light coloured soils. Mix about one part seed with three parts of the bulk material. The different coloured materials make it easier to see where you have been and where you have missed and help to prevent too much seed being dropped in one place.
Step 5: Watering
After sowing, it’s essential that the soil surface is kept continually moist using the finest of sprinklers – heavy watering may cause run-off and wash away some of the seed resulting in patchy growth. Water twice a day to ensure that the soil does not dry out.
Some grasses – particularly ‘Ryegrass’ – germinate within a week under good conditions. Others can take two-three weeks. As the grass grows, reduce watering – in the second week you should water once a day, in the third week, every second day. Twice a week should be ample by the end of the first month. After three months, give your lawn a weekly soaking, except in very hot and drying weather on very light sandy soils.
Step 6: Mowing
Do not begin mowing until your new grass is about 6cm high. Mower blades should be sharp and you should remove no more than 1/3 of the grass length at one time, or use a blade length no lower than 4cm. On future cuts, you can gradually lower the blades, but remember – longer lawns give healthier growth and look more luxurious.
Step 7: Keeping your lawn green
Apply a solid or liquid fertiliser at least 2-3 times a year. Follow directions carefully and water in well to totally dissolve the fertiliser, or you could end up with brown patches or, worse, kill the grass completely.
One deep, uniform soaking per week is usually all a lawn needs, even in hot dry seasons.
Weed & Disease Control
Most weeds can be controlled with a selective weed killer. Some, like Yates ‘Weed ‘n’ Feed’, also fertilise at the same time. Hormone weed killers, such as ‘Zero’ and ‘Round-Up’ should not be used on lawns less than two months old.
Generally, aim to cut no lower than 2-3cm. Cutting at almost ground level is a sure way to kill your lawn and encourage weeds.
Use your pH Soil Test Kit to test for acidity each year. If the pH reading is 6.0 or lower, apply garden lime.
This helps to improve fertiliser and water penetration. Use a hollow tined lawn corer or jab a garden fork into the soil as far as the tines will go. If you do this in spring, less frequent and more effective watering is possible during summer.