Reading nook project
With our premium finishes and on trend effects you can turn an unused corner of a room into a cosy reading retreat. Pairing modern and earthy tones creates the perfect mood for curling up with a good book.
Your shopping list
- Dulux Design Effects in your chosen colours
- Dulux Duramax® in your chosen sheen and colours
- Undercoat/stain blocker (if required)
- High quality synthetic brush for cutting in
- Medium nap (10-18mm) synthetic roller for walls
- Short nap (10mm) synthetic roller for furniture piece
- Paint pot – for cutting in
- Roller tray
- Roller extension pole
- Drop sheets
- Painter’s masking tape
1. Follow the preparation steps on this guide.
2. Start by cutting in around the edges of the wall with a brush – these are areas the roller cannot easily reach.
3. Load the roller in the tray with a reasonable amount of paint.
4. Start rolling the wall in an ‘M’ pattern. Start closest to the natural light source. Continue over the same section until the wall is evenly covered.
5. Using an unloaded roller begin in the top left corner of your wall and gently let the roller roll down to the baseboards in a straight line with no pressure. A lightness of touch will prevent new roller marks from forming. Repeat this action only this time, slightly overlap your last movement so your roller rubs away the line created by the previous stroke. Continue this across the area you have painted. This is called laying off.
6. Reload your roller and repeat until the wall is complete.
7. Working in small sections, apply the second coat with the roller and use a wide brush, dry roller or muslin and drag the paint in a random overlapping pattern.
1. Follow the preparation steps on this guide.
2. Start by cutting in around the edges of the furniture piece with a brush – these are areas the roller cannot easily reach.
3. Apply the first base coat with the roller.
4. Allow drying time as specified on the label.
5. For an even one dimensional finish apply a second coat with the roller and lay off lightly to prevent the formation of roller marks.
6. For a flat finish your project is complete. For a more textured finish, work while the paint is still wet. Use a wide brush, dry roller or muslin and drag the paint in a random, overlapping pattern. For a brushed finish, lay off lightly with a brush. A clear coat may be applied to protect the surface.
1. Follow the preparation instructions for spraying on this guide.
2. If using Dulux Duramax Metallic Finish Gold and Dulux Duramax Black Satin, apply in multiple light, mist coats.
3. Follow after spraying instructions on this guide.
4. Now, admire your transformation! Great job!
What to consider before you start
How much paint do I need?
Use our simple, online paint calculator to determine the amount of paint you need. Head to dulux.com.au/paint-calculator
Protect surfaces and furniture
Remove all furniture from the room. Lay down a proper drop sheet to protect your floors. Try not to use old sheets as paint will often soak through. Mask skirting boards, window trim and electrical switches with painter’s tape. If painting the ceiling, tape around light fittings and any vents.
Already painted surfaces in good condition
If the surface is already painted and in good condition with no stains or mould you shouldn’t need an undercoat. Check the instructions on the product label to determine if a light sand is required. Ensure the surface is clean, dry and free from dust, oils and grease before you start.
Unpainted surfaces in good condition
If you are painting bare, unpainted walls, furniture or ceiling, apply one coat of Dulux® 1Step® Prep over the entire surface. For bare plaster ensure to use Dulux PRECISION® Sealer Binder.
Cracks or holes
Patch any cracks and holes with a suitable filler or sealant, such as Selleys® Spakfilla®® . Lightly sand down the surface to a smooth level then dust off. Apply one coat of Dulux 1 Step Primer Sealer Undercoat over the repairs.
If your walls or ceiling have mould, you will need to remove the mould with Selleys® Rapid Mould Killer™ or 1 part bleach to 3 parts water. Scrub with a scouring pad and bleach solution then leave solution on the surface for 15 minutes. Wash with clean water and wipe dry. To ensure mould does not recur, it is important to eliminate the cause of the mould growth. Several applications may be necessary to remove stubborn mould blooms. Once the mould has been removed and the surface is clean, dry and free from dust, oils and grease, you can paint without an undercoat.
Wash surfaces with Selleys Sugar Soap and if stains persist use a specialist stain blocker to prevent the stains migrating through your topcoat and appearing in your new paint job. The Dulux PRECISION range of specialty stain blockers will have a product to suit your stain problem.
If undertaking a spray project, for ease of application use a Lazy Susan. This will help you spray the object evenly on all sides, without walking in circles or handling it. To help protect surfaces from overspray, use drop sheets, tape or newspaper. Also, ensure the surface is clean and dry, free from grease, rust and dirt. If priming bare steel and iron, or an undercoat is required, use a Dulux Duramax® Undercoat (Metal, Plastic or General Purpose Undercoat). Shake the can for at least one minute before use and regularly during use. After spraying, prevent blocking by flipping the can upside down and spraying until clear gas emerges. Also wipe the front of the nozzle clean.